Results 1 to 10 of 10

Thread: Getting started in engraving

  1. #1
    Join Date
    Jan 2015
    Location
    Leeds, United Kingdom
    Posts
    3

    Default Getting started in engraving

    Friday afternoon and all the orders were out the door so I thought I would have a bit of a play around.I had a go at carving a skull into a 50p piece as pictured Click image for larger version. 

Name:	skull.jpg 
Views:	38 
Size:	55.9 KB 
ID:	7502
    I started off using a mix match of hand pushers that I had picked up somewhere along the way. This was my first attempt at doing anything like this, and whilst doing it, I kind of started to get a feel of how they should work and be used.However, I noticed they got blunt very quickly and I probably ruined them by attempting to sharpen them.

    To finish up, and remove most of the excess I used the cheap power engraver that cousins do. As said, through the process I got that feeling of how it could be done and I am now keen to start exploring and learning how to do it properly.

    I was wondering if anyone could recomend some good books about hand engraving and also what tools are a must have ?

    regards

  2. #2
    Join Date
    Feb 2013
    Location
    Finland
    Posts
    724

    Default

    There are a couple of engraving forums, engraverscafe being the main one...what your doing there is more "carving", there is an art for that on coins generally labeled under "hobo nickels".
    Plenty of help available on the interweb for all that stuff.

  3. #3
    Join Date
    Aug 2010
    Location
    England
    Posts
    1,902

    Default

    This is a good book to start with for engraving; http://www.cooksongold.com/Books/Eng...prcode-999-AMP

    Also this is how I prepare scorpers for use for carving, it may be useful for you to print out for a record;

    Click image for larger version. 

Name:	132a Scorper prep photo sheet.jpg 
Views:	37 
Size:	47.2 KB 
ID:	7503

    James

  4. #4
    Join Date
    Feb 2011
    Posts
    1,743

    Default

    Oh My Gawd! Orf with his head! Defacing a coin of the realm? ~tsk tsk~

    The Morton book is great. I still can't engrave, but I get the idea. I really think it is something that has to be taught.

  5. #5
    Join Date
    Feb 2013
    Location
    Finland
    Posts
    724

    Default

    You shouldn't have to bother with tempering unless you overheated while grinding to shape.
    Only goldsmiths have torches..everyone else can manage without.
    Last edited by Gemsetterchris; 21-03-2015 at 12:15 PM.

  6. #6
    Join Date
    Feb 2013
    Location
    Finland
    Posts
    724

    Default

    Quote Originally Posted by medusa View Post
    I really think it is something that has to be taught.
    Being shown by a teacher is always best, but unless you put in months of practice it won't make much difference.

  7. #7
    Join Date
    Aug 2010
    Location
    England
    Posts
    1,902

    Default

    I have always found new scorpers are hardened too much, which is why I have always rehardened and tempered my scorpers, by following this method I have never had a scorper or graver loose a point or corner when carving. But each to his own.

    Some of my crest carvings;

    Click image for larger version. 

Name:	001c NAG badge enlarged.jpg 
Views:	25 
Size:	41.7 KB 
ID:	7504Click image for larger version. 

Name:	158a SC Haberdashers crest.jpg 
Views:	25 
Size:	70.6 KB 
ID:	7505Click image for larger version. 

Name:	121 Old Fettesians Association des. E.Clements 1969.jpg 
Views:	25 
Size:	42.2 KB 
ID:	7506

    James

  8. #8
    Join Date
    Feb 2013
    Location
    Finland
    Posts
    724

    Default

    That's interesting James. I guess it depends abit on what tool/material people are using..lots of new materials available don't like quenching & wooden handles being replaced by quick release..
    No doubt the "old school" way works fine & I've done it that way ( minus the tempering), but I make tools from square stock & haven't bought a ready shaped vallorbe in years.
    Are people still starting learning from the old traditional way or ..?

    Not that it matters much since tools don't make the result without guidance.

  9. #9
    Join Date
    Feb 2011
    Location
    Scotland
    Posts
    3,437

    Default

    I see nothing wrong in 'old school' or traditional skills Chris, it's how us oldies were trained and we are still here today! It usually means we can make do with much of what we have to hand without spending ridiculous amounts on 'modern' equipment. I know nothing about engraving as it happens but the theory relates to everything. It does mean that we can go on to learn new techniques where appropriate, when it's a bit difficult to to go backwards and learn a skill if you get what I mean..
    I've seen people on here whose first project is casting something they have seen on YouTube without knowing how to use a file or a saw which I'm sure was something you pointed out. Is that not a traditional skill?

  10. #10
    Join Date
    Feb 2013
    Location
    Finland
    Posts
    724

    Default

    I was attempting to point out that there are different "hand push" tool materials/holders available these days which don't require faffing about with wooden handles ect.
    I was taught "old school" & have that t-shirt ..but that's got nothing to do with the methods.
    I don't think everyone these days wants to start with medieval tools even if they are still available.

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •