Results 1 to 10 of 32

Thread: Solder won't flow - soldering bangle join

Hybrid View

Previous Post Previous Post   Next Post Next Post
  1. #1
    Join Date
    Dec 2012

    Default Solder won't flow - soldering bangle join


    Ive searched the other threads on this forum but I can't seem to find the answer for a bangle.

    I have successfully soldered rings closed using solder paste and I have no problems with this. I have had to evenly heat the ring before concentrate on the join and solder flows great. I have also fused fine silver, all good easy even!

    But when it comes to soldering the join for my bangle, the solder just doesn't seem to flow at all. Do I need to evenly heat the entire bangle just as I do with the ring first? I've tried that and also tried using flux and silver solder but its just not working. I've found a couple of vids on Youtube and tried their techniques like clamping the solder with the two ends of the bangle, fluxing and then heating but the darn thing just wont flow for me.

    Here are the videos I've watched:

    Can anyone help me with this? I'm obviously doing something wrong but I don't know what it is

  2. #2
    Join Date
    Jul 2009


    What torch are you using?

  3. #3
    Join Date
    Sep 2011


    Is the solder melting but not flowing through the joint? - uneven heating or not enough heat or the joint is not good enough - gaps.
    Trying cleaning the metal you want to join. One good way to get a tight fit between the two parts is to squeeze them closed then saw through the gap which takes off a sliver but makes for a good tight fit.
    Slosh the flux around and flux the solder.
    make sure it all gets hot enough, if the solder isn't melting at all you simply are not getting enough heat.
    Those are a few things to try.
    Author: Pearls A Practical Guide

  4. #4
    Join Date
    Jul 2013
    Guildford, United Kingdom


    Soldering is still my weak point and I am still learning. I've had this problem a lot on past projects. I discovered medium silver solder was very difficult to work with and now only use either easy or hard. I've worked on pieces that were too large and my hand torch just wasn't powerful enough to heat them properly no matter how long I held the heat on them. (I've ruined many pieces this way)

    I also discovered using my "3rd hand" seems to draw a lot of heat away from the piece it's holding so I no longer use that as (all I have is a little handheld Proxxon torch.) Other times I've had issues if the join wasn't clean enough and/or wasn't sitting tightly together. I often use some lovely titanium clamps to hold things now, they work great and don't seem to draw heat away like the 3rd hand did. I've also learned the solder should begin to flow fairly quickly, in the beginning I was holding the flame on pieces for 20+ minutes waiting for solder to flow. Now if it doesn't happen in a few minutes or so that something is wrong and it's best to stop.
    Last edited by Sandra; 01-05-2014 at 07:53 AM.

  5. #5
    Join Date
    Jul 2009


    I'd echo Peter's question - it sounds like you don't have enough heat.

  6. #6
    Join Date
    Aug 2010


    Good soldering is all about clean surfaces, clean flux, clean solder and clean joins. If you are using silver solder scrape all surfaces and remove any dirty areas, I never use solder paste as I like to see the solder. Then as others have suggested the heat is important, larger pieces are better heated with a soft larger flame, the object is to heat the metal area around the solder joint, up to the flowing temperature of the solder. I am not sure of your experience, but many learners think that you just heat the solder until it flows, which is wrong.
    Another tip is that the solder will flow towards the heat, so after you have heated the whole piece up to near solder running temperature, play the flame on the opposite side of the joint to where the solder sits and the solder will run through the joint, rather than just around it.
    For silver soldering I only use Hard and Easy silver solders, with a Borax cone, borax dish and water as my flux, I flux the interior of the joint, then close it, heat it gently, cut the solder into tiny pieces, pick a piece of solder up with tweezers and dip it into the borax dish, wetting the solder piece with milky white flux, and then it will stick to the heated solder joint before heating the piece to solder flow temperature. Sorry if this is to much info.

    Last edited by Goldsmith; 01-05-2014 at 08:24 AM.

Tags for this Thread


Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts