Search:

Type: Posts; User: art925; Keyword(s):

Page 1 of 18 1 2 3 4

Search: Search took 0.05 seconds.

  1. Thread: Enamelling reds

    by art925
    Replies
    9
    Views
    3,385

    Alastair, enamellers solder has a higher melting...

    Alastair, enamellers solder has a higher melting temperature than hard solder.
  2. Replies
    9
    Views
    2,152

    If I am correct the actual shank looks hollow on...

    If I am correct the actual shank looks hollow on the photos, which will make the re-soldering tricky.
  3. Thread: RIP Jim MIller

    by art925
    Replies
    8
    Views
    4,088

    Sad to read this. Jim will be greatly missed.

    Sad to read this. Jim will be greatly missed.
  4. Replies
    5
    Views
    2,057

    Thompson have recently had a fire in their...

    Thompson have recently had a fire in their workshop so possibly they are still off line. I have had enamels from Enamel Supply in Denmark in the past, good and efficient.
  5. Replies
    9
    Views
    4,493

    whaa, whaa,whaa...

    whaa, whaa,whaa...
  6. Replies
    8
    Views
    2,707

    I use tea lights under a pyrex pot.

    I use tea lights under a pyrex pot.
  7. Thread: Delft clay EU

    by art925
    Replies
    7
    Views
    2,891

    You will find HM group locations closer to you. ...

    You will find HM group locations closer to you. Austria or Germany we have one also here in NL. All sites as far as I remember are offered in English or local language....
  8. Replies
    10
    Views
    4,990

    Black rhodium plating will give you a more...

    Black rhodium plating will give you a more consistent and darker black than obtained with patina.
  9. Replies
    10
    Views
    7,775

    That is fantastic, it makes my boat winch set up...

    That is fantastic, it makes my boat winch set up look basic.
  10. Replies
    13
    Views
    5,640

    Before going back to Cookson, just try one last...

    Before going back to Cookson, just try one last trial....clean your solder with a rub of sandpaper, it could be oxidised.
  11. Replies
    10
    Views
    3,489

    Seems you've cracked it with the second link...

    Seems you've cracked it with the second link Josef.
  12. Replies
    7
    Views
    2,536

    If the item is precious metal, rather than solder...

    If the item is precious metal, rather than solder I think I would advise laser welding; less heat involved, less risk of further damage, easier to clean up after but a specialist could provide better...
  13. Replies
    13
    Views
    8,065

    Give them a call, just because it is not online...

    Give them a call, just because it is not online does not mean it is not available.
  14. Replies
    12
    Views
    3,177

    I am no expert but I will give it a go... Have...

    I am no expert but I will give it a go...

    Have you tried making these with a slightly rounded corner instead of the sharp 90 degrees? I think I remember reading years ago that enamel does not like...
  15. Thread: Buying a bench

    by art925
    Replies
    18
    Views
    4,769

    If you are on the shorter side like me and you...

    If you are on the shorter side like me and you have a specific location to work with I would suggest having the bespoke one made. Think about your chair height, your sitting position and good posture...
  16. Replies
    12
    Views
    7,068

    If you have any powder rouge Sheen, mix it to a...

    If you have any powder rouge Sheen, mix it to a paste with water and paint it on the previous joints, the fat will prevent the solder from re-flowing.
  17. Thread: Weather

    by art925
    Replies
    16
    Views
    6,662

    So this is what we do when the weather allows: ...

    So this is what we do when the weather allows: https://youtu.be/S6pOf2LXovo
    When the pickle in its pot freezes, I know its cold enough to skate. You may recognise Kinderdijk, from C4s Great...
  18. Replies
    13
    Views
    5,630

    ...and there is our next Lounge debate....

    ...and there is our next Lounge debate....
  19. Replies
    5
    Views
    2,711

    just contact your supplier maybe?

    just contact your supplier maybe?
  20. Replies
    5
    Views
    1,617

    Thanks guys for your participation. I have made...

    Thanks guys for your participation. I have made my proposal to my client with the caveat that should it go pear shaped, it will need to be smelted and something new made. I await her go ahead....In...
  21. Replies
    5
    Views
    1,617

    This arrived in the post, what would you do?

    Hi guys,
    I hope all is well with everyone. So this split hollow silver bangle arrived in the post today for repair. I have in mind what I will do to it, what would you do?

    12858
  22. Replies
    2
    Views
    8,416

    I have replied to your previous post on this...

    I have replied to your previous post on this subject....
  23. Replies
    5
    Views
    5,376

    Here are the contact details for the Heimerle &...

    Here are the contact details for the Heimerle & Meule Group Spain, you will have to see for yourself if they supply what you need.

    https://www.sempsajp.com/inicio/
    SEMPSA Joyería Platería, S.A....
  24. Seems its probably the gunk keeping it together.

    Seems its probably the gunk keeping it together.
  25. Replies
    8
    Views
    5,876

    Could you cast them?

    Could you cast them?
Results 1 to 25 of 433
Page 1 of 18 1 2 3 4