Search:

Type: Posts; User: Goldsmith; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    11
    Views
    478

    When cutting silver solder I use a fine blade in...

    When cutting silver solder I use a fine blade in a piercing saw to cut lengthways along the strip of solder and then I use small shears to cut off small squares of solder from the strips. For gold...
  2. Replies
    13
    Views
    705

    I am right handed so I saw from right to left...

    I am right handed so I saw from right to left across my bench peg, also it is important to be seated at the correct height so that you can see clearly where you are piercing. I must admit that I love...
  3. Replies
    13
    Views
    705

    I have a couple of pure bristle painters brushes...

    I have a couple of pure bristle painters brushes on my workbench, they are about half an inch wide, and if I need to clean away any dust from a piercing job's surface, I use one of these, I also saw...
  4. Replies
    13
    Views
    705

    May I say that before I mark out my flower...

    May I say that before I mark out my flower piercing shapes I always polish the surface of the metal so tht the scribed lines stand out clear. As Peter says I always use metal templates to mark out my...
  5. Replies
    15
    Views
    925

    I have always made my own chasing tools using...

    I have always made my own chasing tools using silver steel rods. I use the same method of hardening and tempering as I use when preparing my scorpers for use as I posted earlier on this question....
  6. Before buying from ebay, check out how cheap the...

    Before buying from ebay, check out how cheap the new piercing saw frames are on Amazon, see;...
  7. Replies
    10
    Views
    517

    I love my KCs although I do use my older frames...

    I love my KCs although I do use my older frames for certain jobs. One benefit of the quick release lever shows up when you have multiple holes to pierce, as releasing the tension of the blade then...
  8. Replies
    15
    Views
    925

    Eva, First I cut the silver steel rods using a...

    Eva, First I cut the silver steel rods using a piercing saw, I use regular files to shape the ends of my tools, to harden and temper the punch I use my blowtorch to heat the working end to a red...
  9. Replies
    15
    Views
    925

    I made most of my chasing and line tools using...

    I made most of my chasing and line tools using silver steel and sometimes old broken files. The last silver steel rods I bought from here; https://www.ekpsupplies.com/silversteel.html ,I cut each...
  10. Thread: Gravers

    by Goldsmith
    Replies
    6
    Views
    478

    As Peter says, use a flat scorper with a bright...

    As Peter says, use a flat scorper with a bright polished cutting face, I use many sizes for different jobs with widths from 0.5mm. up to 3mm. I don't use HSS steel ones as mine were all bought before...
  11. Replies
    17
    Views
    1,264

    Nick, one of my egg pendants was worn by this...

    Nick, one of my egg pendants was worn by this princess in the past.

    12489

    James
  12. Replies
    17
    Views
    1,264

    I assume that this pendant has been tested by an...

    I assume that this pendant has been tested by an expert to verify that it is genuine Faberge, in my time I have seen many fake Faberge pieces, looking at the photo of this pendant I would doubt it's...
  13. Replies
    17
    Views
    1,264

    Alistair, The egg was two halves with the hand...

    Alistair,
    The egg was two halves with the hand carved central bezel holding them together and a top mount to hold the jump ring, the pattern under the enamel was machine cut, it's called engine...
  14. Replies
    17
    Views
    1,264

    I made this egg pendant for my sister ten years...

    I made this egg pendant for my sister ten years ago.

    12484

    James
  15. Replies
    4
    Views
    551

    As Dennis said binding wire may help you when...

    As Dennis said binding wire may help you when soldering or else you could perhaps try clamping the piece, like this.

    12454

    James
  16. Replies
    8
    Views
    667

    Do you have a hammerhead attachment for a pendant...

    Do you have a hammerhead attachment for a pendant drill? if so you can grind the hammerheads into various shapes that allow you to hammer textures onto metals, This photo shows some of the textures I...
  17. Replies
    11
    Views
    1,121

    When I have a project to make in precious metals...

    When I have a project to make in precious metals I always make patterns using copper before committing my ideas to precious metals. I buy my copper sheet from this supplier EKP Supplies,...
  18. Replies
    15
    Views
    883

    Jules, the strips that I got from Knew Concepts...

    Jules, the strips that I got from Knew Concepts when they first started selling them are approx 1mm. thick, I rolled some down to approx 0.75mm. thick. Knew Concepts did try some 0.5mm. thick but I...
  19. Replies
    15
    Views
    883

    I rolled my strips down using my old Durston, I...

    I rolled my strips down using my old Durston, I did roll them down at the edge of my rollers and not in the middle just in case the titanium strip marked them, but they didn't leave any marks on my...
  20. Replies
    25
    Views
    1,657

    Hi Jules, the titanium strips mill down down OK,...

    Hi Jules, the titanium strips mill down down OK, I only thin down the ones that I want for tiny jobs, the strips as sold are about 1.3mm. thick and I just mill them down to circa 1mm. thick. They...
  21. Replies
    25
    Views
    1,657

    Sorry to go on about soldering clamps, but I...

    Sorry to go on about soldering clamps, but I think it's worthwhile spending some time making them.

    Someone asked me about a clamp that would hold single claw settings in place on a bracelet and I...
  22. Replies
    25
    Views
    1,657

    Hi Dennis, I do read this forum everyday, but...

    Hi Dennis, I do read this forum everyday, but most of the time the themes are not of interest for me to comment on. These titanium soldering clamps strips that Knew Concepts sell around the world...
  23. Replies
    25
    Views
    1,657

    I thought that we were all metalworkers, shaping...

    I thought that we were all metalworkers, shaping these clamps only takes a few minutes using round nose and flat pliers. I have posted photo sheets before showing how I make them but here is some of...
  24. Replies
    25
    Views
    1,657

    I use home shaped titanium soldering clamps to...

    I use home shaped titanium soldering clamps to hold wires etc in place when soldering, like these ones.
    12330 12331 12332

    Titanium strips available from Cooksons,...
  25. Replies
    6
    Views
    594

    For 3mm thick sheet I would use a larger saw...

    For 3mm thick sheet I would use a larger saw blade, size 0 is the size I would use, but that is probably only because it's the largest in my stock of blades.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4