Search:

Type: Posts; User: Dennis; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.14 seconds; generated 2 minute(s) ago.

  1. Replies
    11
    Views
    469

    No, I agree with Nick. Neither the unequal...

    No, I agree with Nick. Neither the unequal length, not the pitting are acceptable

    They look as if you have been fobbed off, so return them for refund.

    Then buy them from a reputable supplier....
  2. Thread: Cloudy silver

    by Dennis
    Replies
    1
    Views
    154

    Well, there are lots of scratches on it. To get a...

    Well, there are lots of scratches on it. To get a mirror shine on silver, you must faithfully get the best shine you can with each grade of whatever system you are using, and then rotate by...
  3. Thread: Temprature

    by Dennis
    Replies
    7
    Views
    338

    They won't be going for a morning run then Bob?

    They won't be going for a morning run then Bob?
  4. Replies
    1
    Views
    185

    Wild Life Photography

    While waiting for a member to pose a question, you might be inspired by some wildlife pictures:
    https://www.worldnaturephotographyawards.com/winners-2024. 🦎 Dennis.
  5. Replies
    4
    Views
    489

    You might have more success if you created a set...

    You might have more success if you created a set up that allowed you to push harder.
    Hold the ring by the shank in a wooden ring clamp with a screw. Then rest the bezel against something fixed, such...
  6. Thread: Mitre Jig

    by Dennis
    Replies
    7
    Views
    505

    As an amateur, you will have occasional uses for...

    As an amateur, you will have occasional uses for a 45 degree mitre jig, but its main job will be to help you to cut and file the ends of wires, strips and tubes flush.

    The problem will not be with...
  7. Thread: Spinner rings.

    by Dennis
    Replies
    2
    Views
    344

    My way was to waste a little metal by making the...

    My way was to waste a little metal by making the base too wide. Then I had an outside ledge to rest tiny snips of easy solder on. Take he flame away as soon as you see it melt, and trim off the...
  8. Thread: You tube….

    by Dennis
    Replies
    3
    Views
    366

    You can get inspiration from jewellery selling...

    You can get inspiration from jewellery selling sites, not to copy, but to see the trends.

    Also here:
    https://www.atthebench.com/category/all-films/

    https://acj.org.uk/
    ...
  9. Replies
    3
    Views
    637

    You're the star for getting it done. D.

    You're the star for getting it done. D.
  10. Replies
    3
    Views
    637

    Tricky, but if we are talking about round wire...

    Tricky, but if we are talking about round wire (not bezel wire)
    I would spread an even layer of solder onto the backing and sweat the wire on.
    That said, if you use tiny pallions of silver solder...
  11. Replies
    7
    Views
    539

    Yes, overheating wires makes them brittle. Close...

    Yes, overheating wires makes them brittle.
    Close the air hole a little more on your torch if it has one, and/or reduce flame size,
    Keep the flame on the move,
    Work in a darkened area to be alert...
  12. Replies
    9
    Views
    613

    The underside of a ring stretcher will do all the...

    The underside of a ring stretcher will do all the planishing most people require Caroline. I'm hoping you have one.

    However the easiest way to straighten wires is to stretch them, and for that you...
  13. Replies
    19
    Views
    1,490

    I woke up this morning to realise that a small...

    I woke up this morning to realise that a small fly press would do this perfectly in one pass.
    Surprisingly they don't seem to be available any more, except as very old and damaged antiques.
    Maybe...
  14. Replies
    19
    Views
    1,490

    Hello Nathon, I will talk around the subject,...

    Hello Nathon,
    I will talk around the subject, somewhat negatively, as I do, in the hope that something wil be of help.

    You seem to propose spending an extraordinary amount of money just to bring...
  15. Replies
    4
    Views
    806

    Have a look at this.

    Something I put together at the weekend (I wish).

    https://www.youtube.com/watch?v=rUvHyJtETXc. Dennis
  16. Thread: Wire Dies

    by Dennis
    Replies
    3
    Views
    1,008

    Never felt the need, but you would have to use...

    Never felt the need, but you would have to use one blow from a very heavy hammer, or some sort of press, an lots of practice.
  17. Replies
    14
    Views
    2,355

    Good luck with all of that. I hope that what I...

    Good luck with all of that. I hope that what I wrote works for you. Come back if you're stuck.
    Last minute advice:
    Lots of practice with copper.
    Don't be impatient and overload your mill. Once it...
  18. Replies
    4
    Views
    1,258

    Yes a lot of it online is borax substitute for...

    Yes a lot of it online is borax substitute for domestic use.

    If you just need a small amount, you can scrape a borax cone with a knife.

    For a 100 g of powder go to...
  19. Replies
    14
    Views
    2,355

    When is a bargain not a bargain? When it leads to...

    When is a bargain not a bargain? When it leads to a daily gnashing of teeth. Think why they have reduced the price. Obviously because it's not their best seller.

    It's a Durston and that's a plus....
  20. Replies
    5
    Views
    1,372

    It's distinctive though, and sets it apart from...

    It's distinctive though, and sets it apart from the plain ring it could have been.

    Have a think about mica sheet. It is available online for very little money, comes in various thicknesses, and...
  21. Replies
    4
    Views
    1,518

    Fair enough if they want one, but your customer...

    Fair enough if they want one, but your customer has to be warned only to wear it for special occasions, or it will soon be a wreck.
    Take it off for hand washing, and no gardening, or DIY.

    When I...
  22. Replies
    7
    Views
    12,817

    Christmas is coming

    Christmas is coming, so happy Christmas to all our members. Dennis.
  23. Replies
    3
    Views
    18,175

    I haven not mentioned stretching. If you can...

    I haven not mentioned stretching. If you can achieve your aims by rolling only, then the width will remain roughly the same.
    More likely you will have to intercept any tendency to curve (right or...
  24. Replies
    3
    Views
    18,175

    The first question in return Caroline, will be...

    The first question in return Caroline, will be flattened how? Presumably in a rolling mill, and if you carefully feed it through slowly and square on,
    then if you start with L mm of 4.00 diameter...
  25. Replies
    19
    Views
    92,320

    Sticky: Thank you Peter. When you are next in contact,...

    Thank you Peter. When you are next in contact, please send her my regards. Dennis.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4