Search:

Type: Posts; User: art925; Keyword(s):

Page 1 of 17 1 2 3 4

Search: Search took 0 seconds.

  1. Replies
    13
    Views
    275

    Before going back to Cookson, just try one last...

    Before going back to Cookson, just try one last trial....clean your solder with a rub of sandpaper, it could be oxidised.
  2. Seems you've cracked it with the second link...

    Seems you've cracked it with the second link Josef.
  3. Replies
    7
    Views
    248

    If the item is precious metal, rather than solder...

    If the item is precious metal, rather than solder I think I would advise laser welding; less heat involved, less risk of further damage, easier to clean up after but a specialist could provide better...
  4. Replies
    11
    Views
    626

    Give them a call, just because it is not online...

    Give them a call, just because it is not online does not mean it is not available.
  5. Replies
    12
    Views
    441

    I am no expert but I will give it a go... Have...

    I am no expert but I will give it a go...

    Have you tried making these with a slightly rounded corner instead of the sharp 90 degrees? I think I remember reading years ago that enamel does not like...
  6. Thread: Buying a bench

    by art925
    Replies
    18
    Views
    1,508

    If you are on the shorter side like me and you...

    If you are on the shorter side like me and you have a specific location to work with I would suggest having the bespoke one made. Think about your chair height, your sitting position and good posture...
  7. Replies
    12
    Views
    2,078

    If you have any powder rouge Sheen, mix it to a...

    If you have any powder rouge Sheen, mix it to a paste with water and paint it on the previous joints, the fat will prevent the solder from re-flowing.
  8. Thread: Weather

    by art925
    Replies
    16
    Views
    1,657

    So this is what we do when the weather allows: ...

    So this is what we do when the weather allows: https://youtu.be/S6pOf2LXovo
    When the pickle in its pot freezes, I know its cold enough to skate. You may recognise Kinderdijk, from C4s Great...
  9. Replies
    13
    Views
    1,387

    ...and there is our next Lounge debate....

    ...and there is our next Lounge debate....
  10. Replies
    5
    Views
    687

    just contact your supplier maybe?

    just contact your supplier maybe?
  11. Thanks guys for your participation. I have made...

    Thanks guys for your participation. I have made my proposal to my client with the caveat that should it go pear shaped, it will need to be smelted and something new made. I await her go ahead....In...
  12. This arrived in the post, what would you do?

    Hi guys,
    I hope all is well with everyone. So this split hollow silver bangle arrived in the post today for repair. I have in mind what I will do to it, what would you do?

    12858
  13. Replies
    2
    Views
    1,510

    I have replied to your previous post on this...

    I have replied to your previous post on this subject....
  14. Replies
    5
    Views
    776

    Here are the contact details for the Heimerle &...

    Here are the contact details for the Heimerle & Meule Group Spain, you will have to see for yourself if they supply what you need.

    https://www.sempsajp.com/inicio/
    SEMPSA Joyería Platería, S.A....
  15. Seems its probably the gunk keeping it together.

    Seems its probably the gunk keeping it together.
  16. Replies
    8
    Views
    1,245

    Could you cast them?

    Could you cast them?
  17. Replies
    8
    Views
    2,181

    In your flex shaft place 2 sandpaper discs with...

    In your flex shaft place 2 sandpaper discs with backs facing each other, therefore sand side facing top and bottom. Slide the discs inside the cut edges and spin your flex shaft slowly, this will...
  18. Replies
    4
    Views
    1,341

    The video looks amazing, would you be willing to...

    The video looks amazing, would you be willing to share how you went about making the magnetic polisher please? I love tool hacks.
  19. Replies
    7
    Views
    1,302

    Hi and well done with the casting and especially...

    Hi and well done with the casting and especially drilling the hole through. As a tip for next time, if you can position a wooden dowel through the hole of the master when filling with sand and...
  20. Carat of gold plating? thickness of the plating?...

    Carat of gold plating? thickness of the plating? silver tarnish coming through? probably reaction to the packaging, I know the dies used in foam inserts causes tarnish, and glue used in boxes causes...
  21. Replies
    19
    Views
    1,378

    Before making the investment and if you are...

    Before making the investment and if you are wanting a quality ultrasonic, it is a real investment. Following on from what Dennis suggests; I often still turn to my old electric tooth brush, you can...
  22. Replies
    15
    Views
    3,006

    Thanks Caroline, Chocolate makes everywhere a...

    Thanks Caroline,
    Chocolate makes everywhere a better place. I know in the past you have mentioned that you wanted the hammer piece with the Foredom. I have this week found a second hand...
  23. Replies
    15
    Views
    3,006

    Can you expand on why the Foredom micromotor does...

    Can you expand on why the Foredom micromotor does not meet your needs? I am still looking for a micromotor and interested in the Foredom.
  24. Replies
    10
    Views
    14,186

    I have also been known to use the hotgun glue for...

    I have also been known to use the hotgun glue for similar jobs.
  25. Replies
    7
    Views
    2,265

    Let us know if this helps, it will be useful for...

    Let us know if this helps, it will be useful for others in the future as we build upon the wealth of knowledge already here.
Results 1 to 25 of 424
Page 1 of 17 1 2 3 4