Search:

Type: Posts; User: Ruedeleglise; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.01 seconds.

  1. Chacun à son goût! Yes each way works after a...

    Chacun à son goût! Yes each way works after a little practice. Dennis’s is great when the link is so small you can’t get the jump ring to “thread”. In all cases I have wimped out and used easy paste...
  2. Replies
    8
    Views
    347

    PHEW! Don’t think I could justify that...

    PHEW! Don’t think I could justify that outlay….but what a beast!
    David.


    Sent from my iPad using Tapatalk
  3. Replies
    8
    Views
    347

    Now that sounds interesting. Please “keep me in...

    Now that sounds interesting. Please “keep me in the loop”
    David


    Sent from my iPad using Tapatalk
  4. Replies
    8
    Views
    347

    Thanks China. I will investigate David Sent...

    Thanks China. I will investigate
    David


    Sent from my iPhone using Tapatalk
  5. Replies
    8
    Views
    347

    Oh! Not very encouraging. I have seen others...

    Oh! Not very encouraging. I have seen others advertised, so will look around. At least you confirm it can cut the metal even if it has a mind of its own!
    David


    Sent from my iPad using Tapatalk
  6. Replies
    8
    Views
    347

    Powered saw

    Advice again! Are there any powered fine saws for cutting out shapes in silver sheet up to say 1mm or so thick? Having a degree of osteoarthritis in my fingers and wrists, I find this job quite...
  7. Replies
    9
    Views
    416

    Sounds just what the Doctor ordered! Sent to a...

    Sounds just what the Doctor ordered!
    Sent to a direct note….trouble with too full a post box apparently.


    Sent from my iPad using Tapatalk
  8. Replies
    1
    Views
    252

    Mail box too full?

    How do I empty it


    Sent from my iPad using Tapatalk
  9. Replies
    9
    Views
    416

    Thanks…Palmers do have fine tube with a “jump...

    Thanks…Palmers do have fine tube with a “jump ring” one end. I will see if inserting the end of a 1mm or less wide chain into the tube, then injecting easy solder paste around it ……then heating the...
  10. Replies
    9
    Views
    416

    Chain “ends”

    Errrr yes! But with really fine chain however I try using all the tips, tricks and advice I can get hold of, I end up with a blob of meted chain!
    I see there are ends you can bend round the end of...
  11. Replies
    9
    Views
    416

    Thanks yet again! Yes I have replaced my wife’s...

    Thanks yet again! Yes I have replaced my wife’s snake chain more than once with a terminal kink in it. I am not a lover of them! I have some chain now, departing from the “E00 chain!” which is too...
  12. Replies
    9
    Views
    416

    Chain “ends”

    Showing even more of my ignorance now! How is best to end a chain with an attachable ring that one can’t use a jump ring due to either links too small or none as in a snake chain. I have seen various...
  13. Replies
    8
    Views
    345

    Ditto! Sent from my iPhone using Tapatalk

    Ditto!


    Sent from my iPhone using Tapatalk
  14. Replies
    8
    Views
    345

    Well so far, touch wood and being a bit mean I...

    Well so far, touch wood and being a bit mean I have succeeded with the old doming punch technique. I wait for the dreaded split which seems to occur quite often. I am very cautious and start...
  15. Replies
    9
    Views
    582

    Something else to look up and learn...

    Something else to look up and learn about…..great, thanks
    David


    Sent from my iPad using Tapatalk
  16. Replies
    9
    Views
    582

    Micro spot welder…..

    Interesting comments and advice. Thanks. Next question…..where is best to look / buy if I wish to follow this up?
    David


    Sent from my iPad using Tapatalk
  17. Replies
    9
    Views
    582

    Thanks a lot for your observations and advice. A...

    Thanks a lot for your observations and advice. A lot to consider!
    David


    Sent from my iPad using Tapatalk
  18. Replies
    9
    Views
    582

    Thanks Dennis. Yes another possible use. Almost...

    Thanks Dennis. Yes another possible use. Almost worth a gamble as I have seen them for sale at less than £30!
    Come on “others”…….!!!! Let’s have your opinions!
    David.


    Sent from my iPad using...
  19. Replies
    9
    Views
    582

    Micro spot welder…..

    Any advice or recommendations? I am considering one of these for very small chain / jump ring and other very small work. There appears to be a large range, especially in price! From £ hundreds to a...
  20. Sheen, your fame goes before you! I was told you...

    Sheen, your fame goes before you! I was told you were the one to ask! Thanks for your advice.
    David


    Sent from my iPad using Tapatalk
  21. Thanks both of you. Me thinks I am running...

    Thanks both of you.
    Me thinks I am running before I can walk! Problem is that having had successes with rounds and ovals it is only natural to want to go further!
    David


    Sent from my iPad using...
  22. Trust me! I see the problem. I will have to wait...

    Trust me! I see the problem. I will have to wait till the cabs and the bezels arrive and then ponder further with your advice in mind.
    David


    Sent from my iPad using Tapatalk
  23. Setting a square cab into a square bezel.

    I have to attempt this with a 6mm turquoise and am a bit worried about the corners “creasing” Any of you have tips to avoid this perceived problem please?
    David.


    Sent from my iPad using Tapatalk
  24. Replies
    10
    Views
    950

    I did and saw it……there but for the grace of God...

    I did and saw it……there but for the grace of God we can all go. I haven’t so far……,


    Sent from my iPhone using Tapatalk
  25. Replies
    10
    Views
    950

    Well Caro, all went well. No lightening bolts!...

    Well Caro, all went well. No lightening bolts! Hope equally you had success.


    Sent from my iPad using Tapatalk
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4