Search:

Type: Posts; User: WitchfordSilver; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0 seconds.

  1. Hi, the centrifugal casting machine, vacuum,...

    Hi, the centrifugal casting machine, vacuum, plaster, mini casting machine if for sale i would like to get into casting
  2. Replies
    2
    Views
    1,348

    1. microweld 2. i don't use mine a lot so M.E.K...

    1. microweld
    2. i don't use mine a lot so M.E.K just gets changed less than it should. even after 6 months in the booster it still seems to do it's job. same with the water, just top up as it's...
  3. Replies
    12
    Views
    4,258

    Diameter 1.000 MM Length 30000.000 Weight...

    Diameter 1.000 MM
    Length
    30000.000

    Weight 263.89 GM
    £3,127.10 exc. VAT
    £3,752.52 inc. VAT

    i think that you will need to get some soldering equipment as i would hate to see that much gold...
  4. Replies
    50
    Views
    11,187

    And it's a Merry Christmas from me to.

    And it's a Merry Christmas from me to.
  5. Replies
    7
    Views
    3,639

    nice folks got back very quickly and refunded my...

    nice folks got back very quickly and refunded my credit card. sad i liked the mag and will miss it not dropping on the door mat.

    will need to look for a replacement now.
  6. Replies
    7
    Views
    3,639

    I've just renewed my subs and so have just...

    I've just renewed my subs and so have just requested a full refund, before i seek to claim it back with my credit card provider. I don't see how they can take money for one thing and expect you to...
  7. Replies
    19
    Views
    3,744

    So you need to send the scrap or manufacturing...

    So you need to send the scrap or manufacturing waste to the refiner and get them to return the refined material. then you will not be receiving a benefit you will be paying for a service. So are you...
  8. Replies
    19
    Views
    3,744

    not sure if it should be treated as income. if...

    not sure if it should be treated as income. if you spend £10 on silver of which due to manufacturing methods produces £2 of scrap, you don't pass on the cost of the scrap to the customer. if you...
  9. Replies
    25
    Views
    37,144

    Sticky: Web site for ordering, the cook book while...

    Web site for ordering, the cook book while looking for ideas.

    quicker to look at a wider range of findings etc, also helps with remembering what the thing is call so you can put it in the search...
  10. I use easy solder paste in the end cap and hold...

    I use easy solder paste in the end cap and hold the snake chain in a third hand so that it just sits in the end cap but all links are hanging from each other. So there is a gap between them so the...
  11. Replies
    64
    Views
    11,934

    You can always spot a Tuffnels one as they all...

    You can always spot a Tuffnels one as they all have been given names.:)
  12. have you tried these folk's...

    have you tried these folk's http://www.polishingjewellery.co.uk/
  13. Replies
    12
    Views
    2,377

    Very nice looking ring, i like the way the stones...

    Very nice looking ring, i like the way the stones seem to grow out of it. I've made nuggets before and put them on a chain but never though to fuse them together and make a ring.

    Neil
  14. At first I thought I'd just make a gold ring, but...

    At first I thought I'd just make a gold ring, but then a little sparkle is nice.

    Could not think of a easy setting for small stones, so gypsy it was.

    just got a few years now to think up a...
  15. Thanks for the comments, I'll have a look for an...

    Thanks for the comments, I'll have a look for an old burr and see if I can round the end off and have a second go if I can get it off her finger.
  16. My first attempt at a gold and diamond ring

    My first attempt at setting diamonds into a gold ring for my daughters 18th birthday. quite small diamonds 1.5mm just to give it a bit of sparkle.

    Picture taken on my phone at the last minute...
  17. normally sent to the stores for a long weight. ...

    normally sent to the stores for a long weight.

    Neil
  18. in the past i put the clasp into a cup of water...

    in the past i put the clasp into a cup of water with just the jump ring out of the water. But i cracked my cup with the heat:D

    Well i was using a water torch so i was just adding to the water...
  19. 1.5 mm flush set diamonds in 9ct gold ring

    Hi, i'm trying to set 3 1.5mm diamonds in to a small 9ct gold ring.

    Not worked with gold before and finding that the gold is very hard to push over. learning the hard way that it's not the best...
  20. Replies
    4
    Views
    4,086

    Thanks Ann, with these laptops with wide screens...

    Thanks Ann, with these laptops with wide screens i need to scroll down a lot and it was driving me mad.

    Now I can be a much happier visitor

    Neil
  21. Replies
    5
    Views
    4,480

    I alwis cake sure that the speal checaker is...

    I alwis cake sure that the speal checaker is turnned on


    *-)
  22. Replies
    4
    Views
    4,086

    Enrage Vistors

    What is this pop up at the lower right hand screen.

    Enrage visitors! Every time I go to scroll down and the mouse pointer go's over the Yahoo live thing it just pops up and gets in the way. tells...
  23. Replies
    8
    Views
    1,584

    Hope you get an answer Dennis, I have two...

    Hope you get an answer Dennis, I have two syringes full that I stopped using as it was killing my hand trying to get the paste out. Now I dig the paste out with a solder pick and then use two hands...
  24. Replies
    22
    Views
    3,921

    I got one for my mum to sew with for Christmas,...

    I got one for my mum to sew with for Christmas, my brother decided that one would help him! so he got one on ebay from china £12.5 with a lens set.

    When it arrived he said it looks just like the...
  25. Replies
    64
    Views
    11,934

    I tend to open the oxygen tap on the torch before...

    I tend to open the oxygen tap on the torch before I turn on the oxycon and then let it run for about 10-15mins then shut it and light the gass etc. once i turn the flame off- oxy first gass second I...
Results 1 to 25 of 146
Page 1 of 6 1 2 3 4