Search:

Type: Posts; User: china; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    9
    Views
    101

    Have a look here...

    Have a look here https://www.foredom.net/product/p-dp30-drill-press/ https://www.foredom.net/product-category/flex-shaft-tools/flex-shaft-motors-speed-controls/ it really depends on what you...
  2. Replies
    9
    Views
    101

    I have no experience personally, although if you...

    I have no experience personally, although if you want just a drill press I believe the Proxxon has good reviews for a lower priced unit, sadly Dremel are not the high quality items they used to
    be...
  3. Thread: Twisted ring

    by china
    Replies
    3
    Views
    87

    Yes Andrew is a good source of info, I suppose he...

    Yes Andrew is a good source of info, I suppose he goes on a bit for those who are bit less experienced
  4. Thread: Twisted ring

    by china
    Replies
    3
    Views
    87

    Looks good, can be a bit tricky to line up, it is...

    Looks good, can be a bit tricky to line up, it is real handy if you have a reducer stretcher for this type of construction, gives some leeway as you can line it up
    and then make small adjustments
  5. Replies
    10
    Views
    248

    I am in awe at those who engrave the inside of a...

    I am in awe at those who engrave the inside of a rings (hand pushed), I know it is done with the aide of a micro scope, I don't think I will live long enough to be that good
  6. Replies
    14
    Views
    314

    Ah, that explains it, not many jewellers refer to...

    Ah, that explains it, not many jewellers refer to the type of gear I have seen you mention, over time
  7. Replies
    10
    Views
    248

    You can engrave by hand without the use of power,...

    You can engrave by hand without the use of power, with or without power to become proficient takes many hours of dedicated practice.
    Engraving using rotary tools is a very low quality form of...
  8. Replies
    14
    Views
    314

    I have to ask Peter are you or have you been...

    I have to ask Peter are you or have you been involved in engineering or fitting, it is just that over the years I have been on the forum, I have noticed that you seem to use items associated with...
  9. Replies
    6
    Views
    199

    If sending a dagger, to Russia is anything like...

    If sending a dagger, to Russia is anything like sending a dagger ( Dagger/Skian Dubh same thing according to UK customs) to to the UK, I hope he is a very very patient person, I know from recent...
  10. Replies
    6
    Views
    199

    Caroline, your location is listed as as Scotland...

    Caroline, your location is listed as as Scotland maybe "Skian Dubh"
  11. Replies
    10
    Views
    283

    They are great takes me back to the seventies, I...

    They are great takes me back to the seventies, I could not make enough copper pieces to keep up with the demand, every one wanted copper jewellery back then, then all of sudden the craze just died...
  12. Thread: Particulate mask

    by china
    Replies
    2
    Views
    134

    https://rzmask.com/ your location is a mystery...

    https://rzmask.com/ your location is a mystery I'm sure if you check the site they will be able to post to you
    I have no affiliation with this company I am just a satisfied customer
  13. Replies
    7
    Views
    484

    The hammer handpiece will fit all the pendant...

    The hammer handpiece will fit all the pendant motors, just have to be aware to restrict the speed if using a SR rather than the speed limited LX
  14. Thread: Soldering misery

    by china
    Replies
    11
    Views
    384

    Well done, a little bit of advice the picture is...

    Well done, a little bit of advice the picture is not high quality however in my opinion it looks as though you may need to bend the prongs over a little bit more to make the stone more secure
  15. Could also be done with rectangular strip and...

    Could also be done with rectangular strip and bent to shape, it would be more work and take a longer time, if it is more than a one off most likely not feasible
  16. Replies
    9
    Views
    276

    Yep thanks for that, fixed

    Yep thanks for that, fixed
  17. Replies
    9
    Views
    276

    You need to drill a series of holes around the...

    You need to drill a series of holes around the base of the box you have the cylinder in, Propane, LPG, etc. is heavier than air in the event of gas leek it will build up in the box.
  18. Replies
    1
    Views
    91

    I don't use platinum that often, I have never had...

    I don't use platinum that often, I have never had this problem Platinum is known for it's ability to resist tarnish, are you 100% sure you did not contaminate it accidentally, maybe the customer has...
  19. Replies
    9
    Views
    197

    I know just how you feel Deb, if you don't need...

    I know just how you feel Deb, if you don't need it to be a job then just keep it as a hobby and sell items when and if you wish too, of course that is just my personal take on it
    I like to have the...
  20. Replies
    9
    Views
    197

    You don't tell people it moved it is supposed to...

    You don't tell people it moved it is supposed to be like that, makes it more organic
  21. Thread: Christmas gift

    by china
    Replies
    3
    Views
    108

    Good one hand made gifts are always appreciated...

    Good one hand made gifts are always appreciated that little bit more

    "Christmas gift" where has the year gone
  22. Replies
    10
    Views
    312

    I would suggest that you go back and check...

    I would suggest that you go back and check everything is correct i.e., joint is clean, joint is fluxed, solder is clean, solder is fluxed (solder that has been sitting around a longtime can have...
  23. Thread: Glueing pearls

    by china
    Replies
    14
    Views
    8,569

    One way is to make a large bail solder a stem to...

    One way is to make a large bail solder a stem to the bail and glue the stem into the pearl and also glue the bail to the pearl, in place of the cup, as some people do not like the look of the cup
  24. Replies
    5
    Views
    207

    If you do a search on the forum ( top right of...

    If you do a search on the forum ( top right of page ) you will quite a lot of info about pricing
  25. Replies
    10
    Views
    336

    As Peter mentioned the printer must be toner...

    As Peter mentioned the printer must be toner based "not inkjet" sounds to me like that is your problem, in fact using a LASER printer you can transfer the image use a clothes iron
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4