Search:

Type: Posts; User: alastairduncan; Keyword(s):

Page 1 of 6 1 2 3 4

Search: Search took 0 seconds.

  1. Replies
    7
    Views
    59

    Yes, yes, yes. I had to add the other 2 yeses as...

    Yes, yes, yes. I had to add the other 2 yeses as one yes was too short for the forum ;-)
  2. Replies
    25
    Views
    450

    It sounds like you have work hardened metal and...

    It sounds like you have work hardened metal and it's getting springy. When you say hammering, is it a hammer you are using or is it a hammer handpiece with a punch?
  3. Replies
    25
    Views
    450

    You need to hold the base of the bezel firmly so...

    You need to hold the base of the bezel firmly so that you can the push the top over. You've attempted to do this by holding in a vice but this will not be good enough.

    Use some polymorph,...
  4. I have an Eakins scope that looks like the...

    I have an Eakins scope that looks like the components come from the same factory as the Amscope. A review can be found here:

    https://youtu.be/sZqCsk0kGm8

    I'm more than happy with it, and it has...
  5. Replies
    7
    Views
    230

    Thank you all for the lovely comments and advice...

    Thank you all for the lovely comments and advice it is much appreciated. I will take a while longer to decide what to do and when it's completed I'll post the results.
  6. It's the microscope for me as well. As an...

    It's the microscope for me as well. As an alternative style of engraving take a look at Malcolm Appleby's work.

    https://www.instagram.com/malcolm_appleby_engraving

    He uses a scope as well as...
  7. Replies
    7
    Views
    230

    Caddy Spoon

    I know its not jewellery but here goes anyway. I've had this sitting on my bench for a while now, not quite finished. Its a one piece sterling silver caddy spoon which I've hammered, punched, carved,...
  8. Replies
    25
    Views
    450

    If you have to some material the same thickness...

    If you have to some material the same thickness as the slot, you can shove it in and solder it up. It will mean you have 2 solder joints instead of one and you will need to trim up the seat for the...
  9. Replies
    9
    Views
    413

    There is a thorough article examining the...

    There is a thorough article examining the different aspects of firestain here:

    http://www.silversmithing.com/1fire.htm
  10. Replies
    1
    Views
    132

    If you have a torch that you use for soldering...

    If you have a torch that you use for soldering then use that. You don't need anything special. I've used a plumbing torch and an oxy/propane both worked fine. I heat from below on a tripod with some...
  11. Replies
    6
    Views
    200

    You can also use sellotape to hold while gluing.

    You can also use sellotape to hold while gluing.
  12. Replies
    4
    Views
    150

    Great video Josef, the pins seem to be avoiding...

    Great video Josef, the pins seem to be avoiding the skull, would you normally position the pieces to be polished like this or would you put them more in the "stream".
  13. Replies
    7
    Views
    359

    Your casting has come out well. I would have used...

    Your casting has come out well. I would have used a smaller drill so that the wall thickness is larger, with wear it may break through. I agree with you about giving it a try, you may be pleasantly...
  14. Replies
    8
    Views
    329

    Hi Adrian, I've used liver of sulphur a few...

    Hi Adrian,

    I've used liver of sulphur a few times. I have some solid lumps which I dissolved in hot water. It works much more quickly when hot but does give off fumes. Good ventilation and...
  15. Replies
    22
    Views
    780

    They also do smaller packs of straight wire. I...

    They also do smaller packs of straight wire. I bought some on your recommendation. I seem to remember that the delivery was relatively expensive but the up side is that the wire does not need to be...
  16. Replies
    11
    Views
    759

    What is your market? If it's the lower end of the...

    What is your market? If it's the lower end of the market, I suspect it is as you are talking about basic jewellery skills, then you will be competing with countries that have a lower costing labour...
  17. You could try one of these: ...

    You could try one of these:

    https://www.cousinsuk.com/product/tapered-spindles-mini
  18. Replies
    5
    Views
    295

    You have a thumbs up from me Deb.:Y:

    You have a thumbs up from me Deb.:Y:
  19. Replies
    5
    Views
    491

    Hi Harj, Welcome to the party :-)

    Hi Harj,

    Welcome to the party :-)
  20. Put it in some coolmorph or polymorph, set one...

    Put it in some coolmorph or polymorph, set one side then turn over and set the other side. If you are still having problems some gentle persuasion with hammer and punch, this will require a little...
  21. Replies
    8
    Views
    381

    The post is not a complete list and your...

    The post is not a complete list and your processes may differ so I would recommend a test but I'm sure you would do this anyway. You may be able to get a small sample from a supplier.
  22. Replies
    8
    Views
    381

    This popped into my Instagram feed today, it has...

    This popped into my Instagram feed today, it has the properties of a number of different fluxes. You will have to hit the translate link. Hope it helps.

    https://www.instagram.com/p/CCdTnZeirOa
  23. Replies
    8
    Views
    381

    Schauer have 6 different fluxes, its a minefield,...

    Schauer have 6 different fluxes, its a minefield, I should imagine W.G. Ball are the same. You might try contacting them and they may be able to advise on an appropriate flux for your purpose.
  24. Replies
    8
    Views
    381

    I'm not sure I can help you Sandra. I've used the...

    I'm not sure I can help you Sandra. I've used the Schauer as a base for some cloisonne and I don't remember seeing any yellow tint.

    Are you using sterling or fine silver? If it's sterling have...
  25. Replies
    8
    Views
    381

    How did you fire the enamel torch or kiln?

    How did you fire the enamel torch or kiln?
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4