James.
Thank you.
My adjustable regulator has a 0 to 4 setting, (propane). The hose is reinforced high pressure, (safe either way then?). But... am going to go and check out more info' before...
Type: Posts; User: noname; Keyword(s):
James.
Thank you.
My adjustable regulator has a 0 to 4 setting, (propane). The hose is reinforced high pressure, (safe either way then?). But... am going to go and check out more info' before...
Air test your torch first...
Just tested mine this morning...
Blowing bubbles in all the wrong places...
Do the mouth blown torches require any maintenance/cleaning?
Low pressure regulator?/variable regulator?
mizgeorge.
Thank you.
Stuck with what I've got...propane bottle and butane bottle with appropriate regulators, and possibly a lot of heavy breathing.
Got to stick with basic stuff where...
Dennis.
Good point.
That was one of the reasons I asked whether the torch head was interchangable between the two gas sources or whether I needed two torches, one for each gas source.
(I just...
That of course was one of the considerations with the dilemma of propane or butane...as the butane bottle is for the cooker! Seriously...
Then at least I can still use the propane to solder with.
...
Why do I want to use one?... I can not find a suitable alternative, but have not used one before!... What is a good length for the torch to mouth hose? Please.
The micro torch that Dennis suggested...
Hello.... de funked too many micro torches (leaky etc). A large bucket of sand is useful. Currently running off propane bottled gas with needle flame head.
Might go with butane as it may be cleaner...
Purchase. General purpose small scale bench stuff. Practical advice on use. For example; basic stuff...is the head interchangable between propane bottle and butane bottle gas, (suitable regulator on...
Info on mouth blown torches required...options?
Hello, Thank you for your perseverance in chasing up the information, It has, however, confused me further...I will go and have a read of ingredients/proportions...
It is a bit too big to put hot into acid bath...but, the staining from burnt pitch does come off if left in long enough in safety pickle though...prefer to clean with pumice powder and stiff bristle...
ps_bond...I have not used red pitch..,previously only the black stuff...seemed reasonably user friendly...in that it did not seem to cause too much irritation to skin...always a consideration when in...
Dennis...Tried burning it off (outside)...left really troublesome residue...tried acetone...meths...white spirit...eventually stuck it in a paraffin bath...have to fish it out and wipe off pitch as...
Goldsmith, thank you...but curious about the product in cooksons catalogue...just could not find sufficient information, to tell me what it is...other than previously stated...and the fact that it...
Much appreciated, thank you...
"Setters Cement" cooksons 999 681...looked on knowledge base for product information...safety datasheets and product information...but could find no other information other than that provided in...
Possibly...I will wait and see...
Yes...thank you...
Do you have customers permission to use their names?
Are you a cookson's employee?...Are you using actual cookson customer names?...Do you need their permission...?Slightly concerned!
Solderpro 50 did not do as it appeared to say on the packaging...
Had a look at "solderpro 50" torch, it was not suitable for job, (too agressive)... Kiln idea good...but not enough soldering blocks on my bench...didn't need to use two torch method...bit the...
Thank you... had a look at Chaperlaine and Jacobs...found website tricky to browse though...Microtorch was good for manufacture of chain link, but not good for the repair midway along length,...
Thanks for replying. Not sure what 'Go system' is... by 'Taymar' ...resealable, removeable, threaded butane/propane gas canister torch. I use a 'Taymar' type torch and also one of the small butane...