Search:

Type: Posts; User: china; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Thread: Yellow bronze

    by china
    Replies
    13
    Views
    215

    I use Acetylene in the shed, but for jewellery I...

    I use Acetylene in the shed, but for jewellery I use LPG it does not produce that annoying soot I don't want hijack the thread so I will keep quite now
  2. Thread: Yellow bronze

    by china
    Replies
    13
    Views
    215

    I will most likely fire up the Oxy/Acet and test...

    I will most likely fire up the Oxy/Acet and test how they perform on steel, I think they may be 45% and 56%
  3. Thread: Yellow bronze

    by china
    Replies
    13
    Views
    215

    Great Idea Nick, wish I had thought of it, I use...

    Great Idea Nick, wish I had thought of it, I use it quite often.

    P.S. I inherited a large amount of industrial Silver solder rods I have no idea what grade they are.
  4. Replies
    5
    Views
    130

    Classic Not enough Heat "the solder melted...

    Classic Not enough Heat "the solder melted slightly but not much" the item you are soldering melts the solder not the flame
  5. Not a problem glad to be able to help.

    Not a problem glad to be able to help.
  6. Replies
    13
    Views
    290

    Try the solder on another item, does the solder...

    Try the solder on another item, does the solder melt on it's own eg. on a solder block, did you buy the solder from your usual supplier, are you fluxing the join or just dipping the solder ( you say...
  7. Replies
    13
    Views
    290

    " chill Beers " though you liked it warm up there.

    " chill Beers " though you liked it warm up there.
  8. Replies
    8
    Views
    229

    I am the same always used the cheap ones never...

    I am the same always used the cheap ones never had one leak the electrics just break down and are not worth fixing, last time about 4 years ago I bought four as they were on special still on the...
  9. Thread: Sizing cuff

    by china
    Replies
    8
    Views
    160

    I have been in this situation a couple of times,...

    I have been in this situation a couple of times, ask him to cut a thin piece of flexible card the roughly the width of the cuff, wrap it around her wrist cut to length, then flatten out out next to a...
  10. Thread: Stuck silver

    by china
    Replies
    8
    Views
    189

    Just to clarify do have punches that are stuck or...

    Just to clarify do have punches that are stuck or pieces of silver
  11. Replies
    7
    Views
    255

    Soldering would be the way to fix it, however it...

    Soldering would be the way to fix it, however it is not quite that simple, there are most likely more experience on the forumwho can advise you, here is what I know, solid gold you will need tp...
  12. Replies
    7
    Views
    179

    Trepanning would only be if they are circular...

    Trepanning would only be if they are circular discs.
  13. Should be fine I have seen similar, although...

    Should be fine I have seen similar, although always in the first layer, is there any reason why you can't place them in the original layer.
  14. Replies
    11
    Views
    642

    Wards have 1.1mm diamonds...

    Wards have 1.1mm diamonds
    https://www.wardgemstones.com/stones/diamonds/brilliant-diamond-white-si-1-1mm-round.html
  15. Replies
    11
    Views
    642

    The Diamond industry around the world is a Mafia...

    The Diamond industry around the world is a Mafia like enterprise, a few companies such as Wards do not seem to to take part in this, and are happy to sell there products to all.
  16. Thread: Bezel pusher

    by china
    Replies
    13
    Views
    394

    Carefully drill a hole from the under side of the...

    Carefully drill a hole from the under side of the ring and push the stone out
  17. Replies
    12
    Views
    456

    Aris is where two planes meet forming a sharp...

    Aris is where two planes meet forming a sharp edge, in other words knock the sharp corner off.
  18. Replies
    6
    Views
    234

    That's a great mod, I'm out to the shed.

    That's a great mod, I'm out to the shed.
  19. Replies
    2
    Views
    111

    By some of these and make you own...

    By some of these and make you own
    https://magnet.com.au/products/neodymium-disc-3mm-x-2mm
  20. Replies
    12
    Views
    456

    What type of steel are you using, needs to be low...

    What type of steel are you using, needs to be low carbon, unless you have very sophisticated equipment.
    Do you do you own sandblasting, need to protect from rust as soon as it has been blasted,...
  21. Replies
    6
    Views
    156

    Yes that is one theory, however in my opinion it...

    Yes that is one theory, however in my opinion it is a waste of time putting it through the mill will do any thing that hammering will do.
  22. Thread: "Olivia"

    by china
    Replies
    7
    Views
    176

    "Olivia"

    So what are the opinions of "Olivia", would not suit me at all as I tend to use my Mill from the side, to give better access to the piece being processed.
  23. Replies
    6
    Views
    156

    I use one of this type for 90% of the Ingots I...

    I use one of this type for 90% of the Ingots I cast
    https://www.cjservice.com.au/ingot-mould-reversible
  24. Replies
    6
    Views
    156

    As far as I am aware most rolling mills accept...

    As far as I am aware most rolling mills accept about 7mm.
  25. Thread: Family Bling.

    by china
    Replies
    4
    Views
    290

    Some family members will be really happy with...

    Some family members will be really happy with those.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4