Search:

Type: Posts; User: Dennis; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    10
    Views
    362

    Wards are a go-to family firm for professionals....

    Wards are a go-to family firm for professionals. Diamonds are expensive, but they sell all sizes at a price judged to be fair. Prior to Covid, their showroom was always busy to overflowing.
    ...
  2. Thread: Bezel pusher

    by Dennis
    Replies
    13
    Views
    190

    Yes, as the bullet is tapered you will need to...

    Yes, as the bullet is tapered you will need to use your pusher again after gluing, so that the edges don't stand away.
    So I would suggest a two part epoxy, used sparingly not to show, and slow...
  3. Thread: Bezel pusher

    by Dennis
    Replies
    13
    Views
    190

    You will probably have to wiggle it more to make...

    You will probably have to wiggle it more to make it as loose as possible first. Then try the sticky tape. Dennis.
  4. Thread: Bezel pusher

    by Dennis
    Replies
    13
    Views
    190

    Normally you would lay some dental floss across...

    Normally you would lay some dental floss across the bottom of a bezel floor when trying in a stone. Then you can jerk it out if you leave generous ends.

    Failing that precaution, to get out a stuck...
  5. Thread: Bezel pusher

    by Dennis
    Replies
    13
    Views
    190

    If you have a diamond disk, you can make a groove...

    If you have a diamond disk, you can make a groove around it near the base, and push the bezel into that, but frustratingly it will tend to come loose if worn frequently.
    So as Sheena has said, it's...
  6. Replies
    11
    Views
    246

    Yes, lots of things to admire: The red of the...

    Yes, lots of things to admire:
    The red of the garnet goes really well with the darkened silver.
    The outsized flower makes a strong statement, enhanced by the finish of the edges.
    The tube setting...
  7. Replies
    1
    Views
    95

    Have a look...

    Have a look here:https://www.google.com/search?channel=trow5&client=firefox-b-d&q=short+courses+for+jewellers+in+the+UK
    I can recommend Morley College first hand. Dennis
  8. Replies
    11
    Views
    246

    Well done you. Dennis.

    Well done you. Dennis.
  9. Replies
    11
    Views
    246

    If you rivet a metal flower onto a ring, it will...

    If you rivet a metal flower onto a ring, it will be compromised, because the daily leverage will eventually cause it to come loose.
    I see no reason not to add a tube setting and then solder it...
  10. Thread: 18ct white gold

    by Dennis
    Replies
    1
    Views
    64

    Using borax or Auflux/Auroflux, try to melt a...

    Using borax or Auflux/Auroflux, try to melt a clean small snip of your solder on some clean scrap silver or copper. I'm sure it will flow.

    Now provided the joint fits well, and all surfaces are...
  11. Replies
    2
    Views
    131

    Hi David. If you just want the outlines, real...

    Hi David.
    If you just want the outlines, real leaves can be photocopied, adjusted in size and used as labels to cut around.

    To use in a mill, artificial leaves can be obtained from craft supplies...
  12. Thread: "Olivia"

    by Dennis
    Replies
    7
    Views
    147

    They'll fly off the shelves. A new factory is...

    They'll fly off the shelves. A new factory is called for. Dennis.
  13. Thread: "Olivia"

    by Dennis
    Replies
    7
    Views
    147

    Anyone found the price?

    Anyone found the price?
  14. Replies
    6
    Views
    103

    I think it's been said somewhere already, but...

    I think it's been said somewhere already, but ingots benefit from gentle hammering to reduce them before rolling.
  15. Replies
    6
    Views
    103

    All mills are not created equal. For example...

    All mills are not created equal. For example gears and handle length play their part.
    As well as thickness, the length and breadth of the sheet will affect its resistance. I would struggle with...
  16. Cooksons sell a pearl clamp for not very much...

    Cooksons sell a pearl clamp for not very much money, which would probably do the job, and can be held in your drill vice. ...
  17. Thread: Family Bling.

    by Dennis
    Replies
    4
    Views
    212

    Thank you all for looking. Well you are George,...

    Thank you all for looking. Well you are George, part of a very small group of friends. A virtual family in fact. Dennis.
  18. Thread: Family Bling.

    by Dennis
    Replies
    4
    Views
    212

    Family Bling.

    There are several You Tube videos on the effects of twisting square wire, and I woke up one morning with the idea of presenting all my immediate family with a twisted wire ring in 9ct gold.

    The...
  19. Replies
    3
    Views
    252

    The difficulty will be getting the eight sides...

    The difficulty will be getting the eight sides exact Sheena, even with three dividers. The sloping sides are no problem. Dennis.
  20. Thread: Flux

    by Dennis
    Replies
    10
    Views
    260

    Auroflux/Auflux works well with silver solders,...

    Auroflux/Auflux works well with silver solders, with much less bubbling than borax, so that is what many of us prefer to use.

    Easy Flow flux is particularly good for lower melting solders, such as...
  21. Thread: Safety Chain

    by Dennis
    Replies
    10
    Views
    228

    As a rule of thumb, 5.5 - 6.0 cm is about right,...

    As a rule of thumb, 5.5 - 6.0 cm is about right, or you could tie some string loosely around the widest part of the hand, held out flat with the thumb tucked under.
    Cut the string, and subtract the...
  22. Replies
    8
    Views
    287

    If your new big torch has no means of closing the...

    If your new big torch has no means of closing the air hole, then you can still have more control by:

    Not having the gas full on.

    Keeping the flame moving at all times.

    And working in a...
  23. Replies
    26
    Views
    699

    Even if we proposed using SpamOff it would take...

    Even if we proposed using SpamOff it would take months of health and safety checks before we got permission.
  24. Replies
    26
    Views
    699

    They were all replies to ancient threads, but the...

    They were all replies to ancient threads, but the one I opened was at least relevant to the subject, i.e. gemstones. Had they stuck to one or two, they might have been accepted.
  25. Thread: Collar necklace

    by Dennis
    Replies
    11
    Views
    327

    Thank you. Dennis.

    Thank you. Dennis.
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4