Search:

Type: Posts; User: CJ57; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.09 seconds.

  1. Replies
    20
    Views
    229

    Thanks Peter :) I have no idea but looking at...

    Thanks Peter :)
    I have no idea but looking at the offcuts I have I used my piercing saw with a blade that worked! If you are looking for consistent slabs I’d take John up on his offer to cut it for...
  2. Replies
    20
    Views
    229

    Sorry Dan whatís a TPI?

    Sorry Dan whatís a TPI?
  3. Replies
    20
    Views
    229

    You’ll need a heavier blade or even a coping saw...

    You’ll need a heavier blade or even a coping saw but it’s a bit coarse. Beware a fast saw as if almost melts it being resin. The same when polishing on a motor if you use too hard a mop it produces...
  4. Replies
    20
    Views
    229

    Depending on size it’ll cut really easily with a...

    Depending on size it’ll cut really easily with a piercing saw as it’s quite soft
  5. Thread: A Flower Garden.

    by CJ57
    Replies
    3
    Views
    110

    That’s lovely Dennis and much less work in the...

    That’s lovely Dennis and much less work in the end than the real thing!
  6. With such good quality chain available I wouldn’t...

    With such good quality chain available I wouldn’t bother making it either. I only make chains when the design is unusual and suited to the piece
  7. Thread: Carat punch

    by CJ57
    Replies
    7
    Views
    133

    Most of us purchase our makers punch through our...

    Most of us purchase our makers punch through our assay office and don’t have a need for another punch. If we do that for underweight items in the U.K. it doesn’t actually mean anything by law and is...
  8. Replies
    6
    Views
    131

    You are right Anne, the torch isn’t big enough....

    You are right Anne, the torch isn’t big enough. I’ve not found a brŻlťe torch much use for anything but soldering jump rings or balling wire ends
  9. Replies
    9
    Views
    506

    That will definitely aid the design process. I...

    That will definitely aid the design process. I like the more industrial designs and it would be good to see in high definition. I think that is why people have been reticent because they look as if...
  10. Replies
    9
    Views
    506

    Did you make these yourself Rotsco? They seem...

    Did you make these yourself Rotsco? They seem very advanced for someone who is new to jewellery
  11. Replies
    18
    Views
    448

    I didn’t mind it so much originally but sung by...

    I didn’t mind it so much originally but sung by drunken football supporters is:/
    I’ve never been shortened to anything more interesting than Carol by family and Caroline when I was in trouble. Bit...
  12. Replies
    18
    Views
    448

    Oh not Sweet Caroline again! I never thought I’d...

    Oh not Sweet Caroline again! I never thought I’d dislike it so much on its resurgence!
  13. Thread: Hallmarking

    by CJ57
    Replies
    13
    Views
    257

    If there is anything different you need done...

    If there is anything different you need done there is an instruction sheet to attach to your hall note. I usually mark centre back of pendants but they can laser mark in all sorts of difficult places...
  14. Thread: Hallmarking

    by CJ57
    Replies
    13
    Views
    257

    I’ve never had that happen at Edinburgh tbh, but...

    I’ve never had that happen at Edinburgh tbh, but if you feel safer set when it comes back. I usually patina when they come back but then I don’t oxidise the mark usually and keep the backs of...
  15. Replies
    12
    Views
    460

    Hi Larry Surely you must see that the financial...

    Hi Larry
    Surely you must see that the financial outlay is on you to prove they are what you say and fit for use before you try to sell them on. No-one is going to buy them on such tenuous...
  16. Replies
    18
    Views
    448

    I just grip it tight! You can get a nice edge...

    I just grip it tight! You can get a nice edge with a burnisher. Itís a great tool to have for general hand finishing anyway.
    Iíve used one like this since College and Iíve also found it good for...
  17. Thread: Riveting posts

    by CJ57
    Replies
    5
    Views
    139

    For a minute I had to wonder if riveting posts...

    For a minute I had to wonder if riveting posts was a statement or a question:)
    If you tried riveting a post then it would probably turn not being fixed on both sides and fall out As it’s for your...
  18. Replies
    9
    Views
    305

    Doesn’t everyone! I can’t listen to myself and...

    Doesn’t everyone! I can’t listen to myself and apparently no one else can as a video taken for an Open Studio had my picture only:/
    Your voice is clear and steady and it sounds fine to me for the...
  19. Replies
    11
    Views
    415

    I particularly like the the symbol of hope purity...

    I particularly like the the symbol of hope purity and dignity Dennis. Itís something we could all do with
  20. Well I suppose it’s the trade name so probably...

    Well I suppose it’s the trade name so probably the same in all languages ����
  21. Thread: Hallmarking

    by CJ57
    Replies
    30
    Views
    861

    If you think of marking any metal with a punch...

    If you think of marking any metal with a punch then think how it will be supported from behind so that there is metal behind your work to take a hammer blow without denting or deforming the shape. On...
  22. Thread: Hallmarking

    by CJ57
    Replies
    30
    Views
    861

    Set or unset they can’t punch mark behind a...

    Set or unset they can’t punch mark behind a setting only on a flat or curved area of your work. The only way you could have your marks behind a setting would be to laser mark and then I’d set...
  23. Thread: Hallmarking

    by CJ57
    Replies
    30
    Views
    861

    Yes you just stamp your makers mark and send in....

    Yes you just stamp your makers mark and send in. I’m not sure if there is an extra cost to them doing it all.
    Back in the day before technology they took a scrape of each surface so it was all...
  24. Thread: Hallmarking

    by CJ57
    Replies
    30
    Views
    861

    It’s purely a personal choice and gives you total...

    It’s purely a personal choice and gives you total control of where you want it marked.I’m not sure back in the day there was a choice of leaving it with them.Given that they vandalised your work...
  25. Thread: Hallmarking

    by CJ57
    Replies
    30
    Views
    861

    Yes you need a firm whack with an engineers...

    Yes you need a firm whack with an engineers hammer. I can’t read mine anymore either. I get in such a sweat marking mine even after decades that I have mine mostly laser marked
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4