Search:

Type: Posts; User: art925; Keyword(s):

Page 1 of 16 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    2
    Views
    290

    Thanks Dennis, the consensus appears to be 300...

    Thanks Dennis, the consensus appears to be 300 degrees in the oven for about an hour to drive out moisture then coated with borax.

    Cheers.
  2. Replies
    2
    Views
    290

    Pretreatment of a graphite crucible

    Morning all.
    I have a inherited an electric furnace for melting metals. I have had it safety tested and purchased some new graphite crucibles for its use. Question, do I pretreat the graphite...
  3. Replies
    14
    Views
    875

    Brilliant Hack...

    Brilliant Hack...
  4. Replies
    13
    Views
    806

    Jeez I hope I don't have to learn everything the...

    Jeez I hope I don't have to learn everything the hard way! But, as my Dad used to say " if you're learning from a mistake, it was a mistake worth making" (or words to that effect) xx[/QUOTE]
    ...
  5. Replies
    5
    Views
    307

    Hi, I do not have the book, but Stephen...

    Hi,
    I do not have the book, but Stephen Goldsmith is world renowned ....so maybe worth a read of the new book? I am sure it is available at the usual suspect sites, but as I'm not a fan of them I...
  6. Replies
    8
    Views
    520

    I have a fire blanket hung on the wall next to my...

    I have a fire blanket hung on the wall next to my soldering/casting station and I have just noticed that my foam cylinder is out of date....
  7. Thread: Counter enamel

    by art925
    Replies
    2
    Views
    305

    Without a doubt the enamel on the back has been...

    Without a doubt the enamel on the back has been overheated. Is it absolutely necessary to counter? It is usually used to stabilise a piece from buckling out of shape....but sometimes depending on...
  8. Replies
    12
    Views
    669

    So I am happy to say that apart from the infernal...

    So I am happy to say that apart from the infernal noise it makes, I have modified my engraver and it is now a setters hammer and it is perfect. I have rounded off the point and polished it to a...
  9. Replies
    12
    Views
    669

    Thanks Caroline, I think I even have one...

    Thanks Caroline, I think I even have one somewhere in the attic of my workshop...I need to go check it out, do some modification and let you all know the result. thanks guys.
  10. Replies
    12
    Views
    669

    Thanks Dennis & Caroline, good feedback there. ...

    Thanks Dennis & Caroline, good feedback there. So Dennis you modified your engraver by cutting the power cable and inserting a dimmer switch to slow the motor down further? That's worth a try.
  11. Replies
    12
    Views
    669

    Micro motor question

    Hi all,
    I appreciate this topic has been done to death on the forum I lost many hours last night using the search function. However, I do have a very specific question. Would one of the...
  12. Replies
    7
    Views
    652

    Radio 5 Live

    Radio 5 Live
  13. Sterling whether depletion gilded or not will...

    Sterling whether depletion gilded or not will react with all levels of non-uniformity with enamels. If you read up you will see that most people either enamel on fine silver or at least Britannia...
  14. Replies
    6
    Views
    429

    Hi, I'm in NL and here they do not recognise 9kt...

    Hi, I'm in NL and here they do not recognise 9kt gold so 14 is our minimum standard. I have provided a couple of links to two metals pages despite language, it should be pretty obvious when you look...
  15. Replies
    6
    Views
    423

    That's funny!!

    That's funny!!
  16. Replies
    3
    Views
    235

    All of the above, plus remelting silver with a...

    All of the above, plus remelting silver with a strong flame can also introduce oxygen to your mix.
  17. Replies
    6
    Views
    423

    Yep, I know they do stink already, I will cut...

    Yep,
    I know they do stink already, I will cut the edges off and dry out in a secluded area ready to cast in the summer. Thanks so much.
  18. Replies
    6
    Views
    423

    Cuttlefish Bones.

    Picked up some cuttlefish bones up off the beach yesterday. They need drying out and still have the outer shell attached. Will the shell easily detach once they are dry or do I need to do...
  19. Replies
    2
    Views
    224

    Forging a Balloon shape

    Good one for you all.
    For a local competition, I want to forge some balloon shapes then enamel them, so probably best to go without two halves and solder together....so what shape do I start with...
  20. Replies
    2
    Views
    608

    Thanks Dennis, why did I not think of...

    Thanks Dennis, why did I not think of Wards....yep milky will be grade F, I presume.
  21. Replies
    2
    Views
    608

    Milky Aquamarine

    Any pointers much appreciated, looking for suppliers of milky aquamarine facet cut 2/3mm in diameter.
    Thanks!!
  22. Replies
    19
    Views
    1,163

    Missed your question, sorry...Haa I saw at least...

    Missed your question, sorry...Haa I saw at least 2 newly planted forested areas, camped on the edge of one, pledged to return in 20 yrs to see how it has developed.
  23. Replies
    19
    Views
    1,163

    Will PM you Sarah

    Will PM you Sarah
  24. Replies
    1
    Views
    417

    Hi Michael, Not my area of work, but have seen...

    Hi Michael,
    Not my area of work, but have seen this done on You tube online. Is laser welding an option?
  25. Thread: DIY Rose gold

    by art925
    Replies
    6
    Views
    367

    Show us when it is finished.

    Show us when it is finished.
Results 1 to 25 of 389
Page 1 of 16 1 2 3 4