Search:

Type: Posts; User: china; Keyword(s):

Page 1 of 20 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    6
    Views
    111

    Fair enough as I said both my units will go from...

    Fair enough as I said both my units will go from nothing to top speed, I would be letting Foredom know if it a problem they may not be aware of.
  2. Replies
    6
    Views
    111

    If it is a "genuine" Foredom they will repair or...

    If it is a "genuine" Foredom they will repair or replace it under warranty I have never had a problem them, if it is faulty ( rare ) they will fix it, both my Foredom units run from zero to full...
  3. Replies
    8
    Views
    141

    I have all my stamps custom made these days, I...

    I have all my stamps custom made these days, I was not happy with the commercially made ones that I encountered it is more expensive although a well made item will last a lifetime.
  4. Replies
    4
    Views
    413

    Welcome from another Aussie and to the best...

    Welcome from another Aussie and to the best jewellery forum on the net, vertical drawbench that's new "material sizing plate" I guess it is something different to the usual draw plate.
  5. Replies
    8
    Views
    141

    Sounds as though you may need smaller size stamp,...

    Sounds as though you may need smaller size stamp, with a suitable stamp you can stamp wire, it will create a small flat section, that is usually acceptable
  6. Thread: Yellow bronze

    by china
    Replies
    17
    Views
    590

    I don't know if you have Plumbing supply stores...

    I don't know if you have Plumbing supply stores over there we do here they just sell plumbing items many of them will sell Silver solder and brazing rods per rod
  7. Thread: Yellow bronze

    by china
    Replies
    17
    Views
    590

    I use Acetylene in the shed, but for jewellery I...

    I use Acetylene in the shed, but for jewellery I use LPG it does not produce that annoying soot I don't want hijack the thread so I will keep quite now
  8. Thread: Yellow bronze

    by china
    Replies
    17
    Views
    590

    I will most likely fire up the Oxy/Acet and test...

    I will most likely fire up the Oxy/Acet and test how they perform on steel, I think they may be 45% and 56%
  9. Thread: Yellow bronze

    by china
    Replies
    17
    Views
    590

    Great Idea Nick, wish I had thought of it, I use...

    Great Idea Nick, wish I had thought of it, I use it quite often.

    P.S. I inherited a large amount of industrial Silver solder rods I have no idea what grade they are.
  10. Replies
    5
    Views
    139

    Classic Not enough Heat "the solder melted...

    Classic Not enough Heat "the solder melted slightly but not much" the item you are soldering melts the solder not the flame
  11. Not a problem glad to be able to help.

    Not a problem glad to be able to help.
  12. Replies
    13
    Views
    295

    Try the solder on another item, does the solder...

    Try the solder on another item, does the solder melt on it's own eg. on a solder block, did you buy the solder from your usual supplier, are you fluxing the join or just dipping the solder ( you say...
  13. Replies
    13
    Views
    295

    " chill Beers " though you liked it warm up there.

    " chill Beers " though you liked it warm up there.
  14. Replies
    8
    Views
    251

    I am the same always used the cheap ones never...

    I am the same always used the cheap ones never had one leak the electrics just break down and are not worth fixing, last time about 4 years ago I bought four as they were on special still on the...
  15. Thread: Sizing cuff

    by china
    Replies
    8
    Views
    160

    I have been in this situation a couple of times,...

    I have been in this situation a couple of times, ask him to cut a thin piece of flexible card the roughly the width of the cuff, wrap it around her wrist cut to length, then flatten out out next to a...
  16. Thread: Stuck silver

    by china
    Replies
    8
    Views
    192

    Just to clarify do have punches that are stuck or...

    Just to clarify do have punches that are stuck or pieces of silver
  17. Replies
    7
    Views
    258

    Soldering would be the way to fix it, however it...

    Soldering would be the way to fix it, however it is not quite that simple, there are most likely more experience on the forumwho can advise you, here is what I know, solid gold you will need tp...
  18. Replies
    7
    Views
    180

    Trepanning would only be if they are circular...

    Trepanning would only be if they are circular discs.
  19. Should be fine I have seen similar, although...

    Should be fine I have seen similar, although always in the first layer, is there any reason why you can't place them in the original layer.
  20. Replies
    11
    Views
    662

    Wards have 1.1mm diamonds...

    Wards have 1.1mm diamonds
    https://www.wardgemstones.com/stones/diamonds/brilliant-diamond-white-si-1-1mm-round.html
  21. Replies
    11
    Views
    662

    The Diamond industry around the world is a Mafia...

    The Diamond industry around the world is a Mafia like enterprise, a few companies such as Wards do not seem to to take part in this, and are happy to sell there products to all.
  22. Thread: Bezel pusher

    by china
    Replies
    13
    Views
    416

    Carefully drill a hole from the under side of the...

    Carefully drill a hole from the under side of the ring and push the stone out
  23. Replies
    12
    Views
    470

    Aris is where two planes meet forming a sharp...

    Aris is where two planes meet forming a sharp edge, in other words knock the sharp corner off.
  24. Replies
    6
    Views
    238

    That's a great mod, I'm out to the shed.

    That's a great mod, I'm out to the shed.
  25. Replies
    2
    Views
    113

    By some of these and make you own...

    By some of these and make you own
    https://magnet.com.au/products/neodymium-disc-3mm-x-2mm
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4