Page 1 of 2 12 LastLast
Results 1 to 10 of 18

Thread: How to seal a jump ring

  1. #1
    Join Date
    Aug 2009
    Location
    West London
    Posts
    5

    Default How to seal a jump ring

    Hi Everybody,

    I am new to the Forum and I was hoping if one of you could help me with a quick question.
    I would like to know how I could permanently seal jump rings without soldering them. When they are small and quite bendy, they sometimes open and little items like charms fall off... I was wondering if there was a product like a sealant (a bit like superglue?) which one could use for gold, silver or even dark coloured metals like brass?

    Thanks in advance,

    Lolinha

  2. #2
    Join Date
    Jul 2009
    Location
    Rye Foreign, East Sussex
    Posts
    2,221

    Default

    Hi Lolinha welcome to the forums.

    I am afraid i am a noob so i cannot answer your question but no doubt one of the clever ones will be along any minute
    Su' xx

    My FB fanpage -https://www.facebook.com/CintaHandCraftedJewellery
    My Website www.cintahandcraftedjewellery.co.uk

    I want to learn so much, and i want to know it all NOW!!!:p

    One day i will arrive

    A huggle a day makes the bad stuff go away

  3. #3
    Join Date
    Aug 2009
    Location
    Doune, By Stirling, Scotland
    Posts
    27

    Wink

    Hiya and welcome.

    The bad news is that no, glue isn't advised, cheats never win!(as my Dad would say) The best thing is to solder them, I'm afraid. If they are not able to be soldered (due to enamel on the charm or suchlike) then I would suggest making your jumprings a lot heavier - say 0.5-0.75mm and work them well side to side, overlapping to close over well, give them spring and harden at the same time, do you know what I mean?
    Hope this helps.


    Nikki

  4. #4
    Join Date
    Jul 2009
    Location
    cotswolds
    Posts
    3,383

    Default

    Alternatively, and especially for charms, you could use a split ring. In places where you're needing to join a particularly fine wire or thread, an oval jump ring can be useful too.
    (and welcome from me too )
    Last edited by mizgeorge; 26-08-2009 at 10:55 AM. Reason: add welcome!

  5. #5
    Join Date
    Aug 2009
    Location
    West London
    Posts
    5

    Default

    Hi again and thanks to everybody who took the time to reply and your warm welcome.
    Sorry I was offline for a few hours...

    I did suspect the answer was going to say that there was no alternative to soldering...
    However, I will follow some of your advice - split rings and oval jump rings - thanks, Mizgeorge.

    Nikki, I can't really go much heavier than the smallest (or almost the smallest) for the jump rings, as I am working with very fine gold thread and the rings I am using can't be too thick. I am not sure I understand what you mean in your last sentence (I understand the overlapping bit...)...

    Any other suggestions, anyone out there?...

    Lolinha

    PS- Does anybody know where I could find some really interesting (I want to say 'funky', but certainly do not mean it in a blasphemous way) religious medals (colourful and bling) and some interesting charms (large, fun and colourful, not your usual sweet enamel slipper or pewter teddy bear)?
    I have tried eBay and found some, but looking for ideas...
    Thanks again,
    L.

  6. #6
    Join Date
    Aug 2009
    Location
    Doune, By Stirling, Scotland
    Posts
    27

    Red face Jumprings

    well, you know when you've got your jump ring in your two sets of pliers, and you push the two ends over each other, to the side to form an over lap, then bring it back to the centre to "ping" it shut with the spring pressure you've created? Do it another couple of times, to each side before you bring it back to the middle. Not too much or you'll snap it, but enough to workharden it a bit. Sorry it's really hard to explain with out showing you or drawing a pic, hope you acn understand my ramblings. The splitrings sound your best option, to be honest, Georege is the jumpring master!

    Nikki

  7. #7
    Join Date
    Aug 2009
    Location
    West London
    Posts
    5

    Default

    Ok, Nikki, much clearer, but that's what I thought I'd understood - so wasn't bad at all first time around!... Thank you.

    Split rings. Ok, splitring master George (or Nikki!), can you explain how to use them without damaging them. I tend not to use split rings because I find that I can never close them back properly once I have slid something into them. They don't seem to 'spring' back into their original shape and stay slightly open. What I am doing wrong?
    By the way, I am self-taught, so please bear with me if I am asking obvious questions...

    Any thoughts on the 'PS' part of my last posting anyone?

    Lolinha

  8. #8
    Join Date
    Aug 2009
    Location
    Newcastle
    Posts
    76

    Default

    hmm there is one more way which is take to your jewellers who has a lazer machine and then he can zap it closed for you.

  9. #9
    Join Date
    Jul 2009
    Location
    midlands
    Posts
    228

    Default

    ................................
    Last edited by ben b; 13-09-2009 at 01:46 AM.

  10. #10
    Join Date
    Aug 2009
    Location
    West London
    Posts
    5

    Default

    Thanks, Mat, I will bear that in mind next time I make a precious piece with just a few rings. The ones I am making at the moment have too many of them and it would probably end up costing me quite a lot...


    Hi Ben,

    Nice to see that the Forum members have a sense of humour!...
    If I ever get to a point where I have to steal a jump ring, I shall certainly get in touch for advice...
    In the meantime, nobody has picked up my request regarding funky medals and charms...
    Any suggestions, anybody?

    Lolinha

Similar Threads

  1. Replies: 9
    Last Post: 05-05-2010, 09:41 AM
  2. Jump Ring cutting
    By Bernie in forum Beading & Lampworking
    Replies: 30
    Last Post: 31-03-2010, 07:12 PM
  3. Jump rings - help
    By vsilvered in forum Maille and Wirework
    Replies: 5
    Last Post: 09-02-2010, 11:52 PM
  4. Jump ring cutter
    By WitchfordSilver in forum Customer Service
    Replies: 0
    Last Post: 21-12-2009, 10:53 PM
  5. Jump rings
    By Milomade in forum Need Help? Ask the Experts!
    Replies: 15
    Last Post: 03-08-2009, 07:59 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •