I’ve had a sievert forever and see no reason to change now.
I’m about to back you Caro as it’s worth shooting around for everything now as I have found Cookson is not the cheapest just convenient
I’ve had a sievert forever and see no reason to change now.
I’m about to back you Caro as it’s worth shooting around for everything now as I have found Cookson is not the cheapest just convenient
I didnt see your note until I had already bought a Sievert from Cooksons. I bought the beginners one as I already had a regulator, only to find to find that the handset equipment already has a regulator built in. I couldnt get it to work initially and the Flogas chappie didnt know either, only to find out yesterday that there is a black button on the setup that sends the gas up the pipe. I tried the burner they sent but it was a bit fierce, so I ordered the 8mm one. Most of the stuff I make is delicate things like earrings. Hope the smaller one will work OK. Still haven't found out what the black button on the regulator does, unless it only sends the gas through.
Last edited by Patstone; 13-08-2023 at 07:05 AM.
I think you have what is called a hose failure valve rather than a regulator. The little button will pop out if it detects any sudden change of pressure like a damaged hose. Small to large interchangeable nozzles have a tiny jet in them that controls the gas flow. If you change a nozzle without turning the gas off this may also cause the button to pop out. As well as removing the valve from the bottle will activate the button … N
Nicks creative stuff on YouTube
https://www.youtube.com/channel/UC_L...rf9BHtKU4lFUhQ
No need for a regulator with this set up. The button is a safety device and stays pressed in and the gas will flow. it will only pop out and cut off the supply if it detects a sudden change in gas pressure like when you disconnect the bottle. After reconnecting a bottle simply push it back in again and away you go Nick
Last edited by nicks creative stuff; 13-08-2023 at 02:19 PM.
Nicks creative stuff on YouTube
https://www.youtube.com/channel/UC_L...rf9BHtKU4lFUhQ
The button is pushed in and there is no gas coming out of it. My next plan is to take off the hose connector thingy to hope that the button will pop out. I am 76 yrs old and haven't got a man to undo it for me, but spoke nicely to my neighbour and he is coming in tomorrow after work to undo it for me. I just hope it works. Pat
I don't think I was logged in when I replied to you.
The button is in at the moment and no gas. I can't undo the hose thingy as I haven't got the strength in my hands now (I'm 76) and haven't got a man to do it for me.. However I have got a nice strong neighbour who offered to undo it for me after work tomorrow. Just hope it works opposite to what you said !!!!!!! Pat
Sorry that you’re struggling with your kit Pat, if you’ve had it working I’m sure it should run again. Try this sequence once more … connect a large flame nozzle to your hand piece (it may take time for air to bleed out of a small nozzle) … make sure the tap on the hand piece is turned off … have the valve on the end of the hose connected to your bottle … turn the bottle on … push the button in … now turn on the tap on your handpiece and ignite … hopefully… N
Last edited by nicks creative stuff; 13-08-2023 at 05:47 PM.
Nicks creative stuff on YouTube
https://www.youtube.com/channel/UC_L...rf9BHtKU4lFUhQ
Tried the nozzles on the gas setup and it was good I took it out in the garden as it caught fire, turned the bottle of gas off and had to chuck water on it to put out the flames.
I would be interested to know what other people use to solder their items with. Answers needed, as I have spent over £130 so far.
Pat
Last edited by Patstone; 15-08-2023 at 01:50 PM.
Bookmarks